99 - V6 Full Part Out - Salvage Car !! Toronto, Canada

[HDavidB]

As the Title States this is a Full Part Out !!
I’m an MR2 owner/forum/club member and can provide forum names both Canada & USA as references.

The Engine/EVAP, Manual Trans, Gauges & Complete Electrical system will be used for my 91 MR2 project.
Everything else is for sale. Car is 30% stripped and will be completely torn down by early Dec.

99 – V6 Manual Trans. - Blue Ext. Grey Leather Int., Glass Power Sun Roof.
Nice sounding MEGAN Cat back being sold with “Y” pipe & Cats !! $250 or Best Offer ?
Leather Seats fronts/rears ( good condition ) $300 or Best Offer ??
Willing to ship smaller parts, larger items of course cost big $$$ and are better sold locally.

http://toronto.kijiji.ca/c-cars-vehicle ... Z330634501

Above is my Local Kijiji add.
Note: Hood, Front Bumper, Pass Fender & Headlight already sold !
Also sold a bunch of smaller items to “boostedcamry” in the USA MR2 forum http://www.mr2oc.com.

I’ll post photos in this thread once I get them uploaded into photobucket.
I can email any photos from my iPhone if requested.

SOLD ITEMS:

Hood, Front Bumper, Pass Headlight & Pass Fender, Washer Bottle.
Front Marker Lights, Drive Fog Light, ALL ABS sensors, Clutch & Brake Pedals.
Shifter Assy Complete, Front 4 Speakers JBL, Center Console Lid, Sun Visors.

[Mr_Krispy1183]

If you've got all 4 ABS sensors, I'll take them

[HDavidB]

If you've got all 4 ABS sensors, I'll take them

Sorry... this is one of the sold items already !!

I'll place a list in my orginal post to show what is sold.

[HDavidB]

If you've got all 4 ABS sensors, I'll take them

Sorry they are sold already !
Actually 1 was broken in the car and the 3 remaining are sold to an MR2 buddy who has a Wicked Solara !!

[minig646]

Got an intact rear cupholder assembly? Every one i see at junkyards is busted like mine. I'd pay $20 for a good one.

Also, how're the gas shocks that hold up the hood? Mine are worn and the hood won't stay up if it's less than 50 degrees out. I'd probably be willing to pay 10-15 bucks for a good used pair.

I also need the driver's side inside door handle bezel- I bent mine up when I removed it last time. Pretty minor and probably not worth the trouble for you to go and remove it without bending it, but I may as well ask.

[mig0s]

PM'd you.

[1gSE]

do you need the torque rod bracket for the swap? If not I'll take it

[HDavidB]

Hey Guys, I'm having a busy family weekend.. I'll reply to each post later today or monday morning, Thanks !!

[HDavidB]

Got an intact rear cupholder assembly? Every one i see at junkyards is busted like mine. I'd pay $20 for a good one.

Also, how're the gas shocks that hold up the hood? Mine are worn and the hood won't stay up if it's less than 50 degrees out. I'd probably be willing to pay 10-15 bucks for a good used pair.

I also need the driver's side inside door handle bezel- I bent mine up when I removed it last time. Pretty minor and probably not worth the trouble for you to go and remove it without bending it, but I may as well ask.

I've had a few requests for the cup holder and sadly so it's broken, poor design on that piece !!
The hood shocks I have and are in good condition. The door handle bezel I'll have to double check ( I have the panel off already to get the wiring out )
PM me with an address and I'll get a quote postal service ship to you.
Thanks.

[HDavidB]

do you need the torque rod bracket for the swap? If not I'll take it

Kalimera,
Not sure which part this is ?
But if I don't need it, I'm more than willing to sell & ship it to you.
My wife's family is from Thessaloniki and I'm sure I can talk her into delivering it in Person
PM me with more info about the part ??
Thanks,
David B.

[1gSE]

kalispera (its just after 6pm here)

Here's a few pix,





As you can see, mine is cracked. Is there some sort of priority shipping in Canada? Mail takes forever getting here if it goes by surface

[HDavidB]

kalispera (its just after 6pm here)

Here's a few pix,

As you can see, mine is cracked. Is there some sort of priority shipping in Canada? Mail takes forever getting here if it goes by surface

Okay... now I know which part and it won't be used in the MR2 Swap.
Mine is different from yours.. it has a little Shock Absorber ?
Guess that is why yours cracked !!
PM me your email address and I'll send you a photo I took with my phone.

It's best I ship you the whole thing, shock & upper lower brackets.
I'll keep it aside for you and ask my Father In Law what is the Best way to ship to Crete.
One way or another I'll make sure you get it !!

Once I figure out shipping I'll PM you for the proper address.

[1gSE]

I used to have a shock absorber, thats Jim's torque rod on it now. Pretty common mod, especially for us sc'd guys. IIRC its supposed to help limit engine movement. A few guys have cracked it in the past, and after reading up on it, its mostly due to over tightening the nut....and I remember cranking down on it pretty good when I first installed it lol

[HDavidB]

I used to have a shock absorber, thats Jim's torque rod on it now. Pretty common mod, especially for us sc'd guys. IIRC its supposed to help limit engine movement. A few guys have cracked it in the past, and after reading up on it, its mostly due to over tightening the nut....and I remember cranking down on it pretty good when I first installed it lol

Okay... then it's just the bracket, makes the package smaller/lighter to ship.

I haven't got the engine out but will have it out later this week.
I'll get back to you soon !!

[1gSE]

Ok cool. I also use a state side company to ship things here, it that's easier for you