SUPRA TT BRACKETS PICTURES PG.8

[CASTRO]

damn i just read what i posted. hahaha! i wont change it though cause I think its cool and I'm sooo buzzed right now. And yeas, I just got off work and it is 7pm mwahahahhaha

[gnegroni]

Thanks for both krawzyazn and Camrazy for the Gen2 info.

As for Castro...
As long as you don't leave work at 10pm, its AOK.

[Dawgz]

Thanks for both krawzyazn and Camrazy for the Gen2 info.

As for Castro...
As long as you don't leave work at 10pm, its AOK.

Milt comes in for the SAVE!

[Sp33d]

They do NOT fit the Gen 2. Gen 2 Rotors are bigger than Gen1 but smaller than TT which will cause the caliper to sit halfway in the air and half of the pad will sit on the rotor.

I had these Brackets before and I tried them on Posh's ride and it didn't work out.


Interchanging the BBK was a different story since the BBK Calipers sit on a bracket with Studs meant for the Caliper, so no matter what It will always cover the rotor, That is why I just went out bought a set of brackets for my SC and the Stoptech's are on there now.

I wasn't going to post on here but I would hate to see The Gen2 guys waste money on this while it will not work for them. It would suck if you guys ask for your money being back and this guy refusing to return money being the tight wad that he is.

Here is a a pic of the difference in rotor sizes.

thanks for the info milt. its much appreciated.

-Mark

[JvR]

I am in to. ...... my girlfriend demands me to buy it because i always drive far above the speed limit (160Km/h).
ofcourse they must fit my camry v6 1998


1.trdkamuri51o
2.dat1krazypinoy831
3.r0w
4.Solarizona
5.hskrsolara (Quentin)
6. NVDIS1
7. akora12
8.lightear
9. JvR (I have send you a pm)

Just 1 to go...... that must be easy.
I hope the y-pip GB will just go as fine like this one

[CamryOnBronze]

Ill take the last set:

1.trdkamuri51o
2.dat1krazypinoy831
3.r0w
4.Solarizona
5.hskrsolara (Quentin)
6. NVDIS1
7. akora12
8.lightear
9. JvR (I have send you a pm)
10. CamryOnBronze

[ASG14]

ofcourse they must fit my camry v6 1998

I've helped a friend install these on a '97 V6. It will fit your car fine.

[JvR]

Thanks! my girlfriend will be happy ...but me more

[Sp33d]

ill take five back up reserves in case the first ten bail.

if by the end i do not get anyone that backs out, i will keep the names of the five for the next batch of brackets.

-mark

[YESCA]

When are these being made.. I can't believe I missed this thread and the GB... FUDGE!

[Solarizona]

Anyone have a set of rotors picked out to go with these brackets? I want something besides Brembo blanks as my current set have already warped after only 20k miles.

[trdkamuri51o]

yesca just put your name up.. just in case as a backup someone will praly flake out (though i kno it wont be me lol)

[STYLSH]

The gen4s camrys have single piston calipers only. However the twin piston calipers off a gen 3 is a simple swap to the gen 4 camrys. No mods needed. I'm running them on my gen4.5 atm.

[JavaJoe_2]

Anyone have a set of rotors picked out to go with these brackets? I want something besides Brembo blanks as my current set have already warped after only 20k miles.

Ikuta's
I believe those are the right ones. I'll check the install instructions.
edit:

oem Supra TT

[Solarizona]

Ikuta's
I believe those are the right ones. I'll check the install instructions.

Awesome. Thanks.