[phpBB Debug] PHP Notice: in file /viewtopic.php on line 988: date(): It is not safe to rely on the system's timezone settings. You are *required* to use the date.timezone setting or the date_default_timezone_set() function. In case you used any of those methods and you are still getting this warning, you most likely misspelled the timezone identifier. We selected 'Europe/Moscow' for 'MSK/3.0/no DST' instead
[phpBB Debug] PHP Notice: in file /viewtopic.php on line 988: getdate(): It is not safe to rely on the system's timezone settings. You are *required* to use the date.timezone setting or the date_default_timezone_set() function. In case you used any of those methods and you are still getting this warning, you most likely misspelled the timezone identifier. We selected 'Europe/Moscow' for 'MSK/3.0/no DST' instead
SolaraGuy.com • View topic - Anti-Sway Bar DIY: Gen 4 Camry Gen 1 Solara
Non-tutorials will be deleted.

Anti-Sway Bar DIY: Gen 4 Camry Gen 1 Solara

Anti-Sway Bar DIY: Gen 4 Camry Gen 1 Solara

Postby MentatGom » Mon Mar 21, 2005 11:32 pm

Gen 4 Camry/ES300/Gen 1 Solara Anti-Sway Bar Do It Yourself

Estimated Time Of Completion: ~2.5 hours

Tools / Materials:
hydrolic jack
adjustable jackstands (2)
torque wrench
socket wrench
21mm 6-point deep socket
14mm 6-point shallow socket
12mm 6-point shallow socket
10mm 6-point shallow socket
socket extension
12mm 6-point boxed end wrench
12mm 12-point boxed end wrench
5mm hex wrench
WD-40
Yellow Gasline PTFE Tape (Durable Teflon Tape)
Image

Note: Spray the anti-sway bar links and brackets with WD-40 at least a day before you plan on working, it really helps.

Rear Anti-Sway Bar Removal:
1.Loosen wheel nuts (21mm)
2.Raise the rear of the car (jack up by the dimple in center of frame crossmember)
3.Support with jackstands (at appropriate rigid frame points)
4.Remove rear wheels
5.Remove rear muffler heat sheild (10mm and extension, 3 screws, 1 clip, near middle of car)
Image
6.Disconnect left and right anti-sway bar links from the bar (14mm)
7.Remove the anti-sway bar brackets and bushings (12mm socket)
8.Remove the anti-sway bar

Rear Sway Bars:
Image
Before:
ImageImage
After:
ImageImage

Front Anti-Sway Bar Removal:
1.Loosen wheel nuts (21mm)
2.Raise the front of the car (jack up by the dimple in center of frame crossmember)
3.Support with jackstands (at appropriate rigid frame points)
4.Remove front wheels
5.Disconnect left and right anti-sway bar links from the bar (14mm)
6.Remove the anti-sway bar brackets and bushings (12mm 6-point boxed end wrench for initial loosening, use 12mm 12-point to remove once loose, note this is a very tight space)
7.Remove the anti-sway bar (must remove the bar from the left side of the vehicle, while under the vehicle slide the bar slightly left then push it up into the slight gap available, then proceed to slide it left and out)

Front Sway Bars:
Image
Before:
ImageImage

After:
ImageImage

Installation of your hardware is just the reverse process of removal.

Additional Notes: To prevent bushing binding that results in squeaking, wrap the anti-sway bars with the teflon tape at the bushing mount points.
Image

The 5mm hex wrench can help out if pushing the endlink through the anti-sway bar end is a bit tight, you can use it to thread the endlink through.

When working on the front anti-sway bar, turning the steering wheel left or right can help give you additional clearance and room to work in.
After the car has been lowered back down go ahead and try to tighten up the endlink bolts again, as you will have more clearance to fit your wrench in.

Torque Specifications for installation:
Anti-sway bar links = 29 ft/lbs (same front and rear)
Anti-sway bar brackets = 14 ft/lbs (same front and rear)
Wheel nuts = 80 ft/lbs

A DIY by Gom
Last edited by MentatGom on Fri May 26, 2006 1:56 am, edited 5 times in total.
MentatGom
Just Licensed SolaraGuy
 
Posts: 48
Joined: Mon Nov 29, 2004 6:21 pm
Location: Moreno Valley, CA

Postby SleeperSolara » Tue Apr 04, 2006 7:47 am

Nice man.

Also to add to that even though you torque them down right they can still be undone some how.
Don't ask me how but it happened to me.....
So use Thread lock on them.
2000 Solara SE auto V6. Diamond White Pearl.
Top Speed Run finished at 130 mph. :o
Too many modifcations for the signature.
User avatar
SleeperSolara
SolaraGuy Hall of Famer
SolaraGuy Hall of Famer
 
Posts: 9257
Joined: Tue Jun 15, 2004 11:38 am
Location: The 405

Postby TripleBlack » Fri Jun 16, 2006 9:49 am

Excellent. Thanks, man.

So, where'd ya buy the new bars? =)
Proud member of the 49.8% which paid attention last time.
TripleBlack
Regular SolaraGuy Member
Regular SolaraGuy Member
 
Posts: 60
Joined: Tue Jun 06, 2006 8:20 pm
Location: Wayne, NJ

Postby Hsakuragi » Fri Jun 16, 2006 10:15 am

Nice,

But for rear..

step 1, 4 and 5 is not necessary for some people..(like me)

Good job though.
The ONE & ONLY Fully Loaded 2006 X Avalon Limited with Body Kit in CA = Special Limited Edition + First 2GR-FE rebored the throttle body (i think...)

Image
Hsakuragi
SolaraGuy Semi-Pro Racer
SolaraGuy Semi-Pro Racer
 
Posts: 3509
Joined: Sun Dec 29, 2002 10:50 pm
Location: Bay Area, CA

Re: Anti-Sway Bar DIY: Gen 4 Camry Gen 1 Solara

Postby Jai_Jai_Binks » Fri Jun 16, 2006 10:52 am

MentatGom wrote:Additional Notes: To prevent bushing binding that results in squeaking, wrap the anti-sway bars with the teflon tape at the bushing mount points.


Great suggestion.
User avatar
Jai_Jai_Binks
Desi SolaraGuy
Desi SolaraGuy
 
Posts: 5751
Joined: Fri Jul 12, 2002 11:59 am
Location: Friendswood, TX

Postby TripleBlack » Fri Jun 16, 2006 1:10 pm

Okay, but seriously .. where did you buy the bars? I've been searching here, there, and everywhere. I don't know why I'm having such trouble finding these things. =(
Proud member of the 49.8% which paid attention last time.
TripleBlack
Regular SolaraGuy Member
Regular SolaraGuy Member
 
Posts: 60
Joined: Tue Jun 06, 2006 8:20 pm
Location: Wayne, NJ

Postby xavier » Fri Jun 16, 2006 3:09 pm

check the for sale section. THere is a TRD kit and RSB for sale right now
Bixenon projector retrofit done! http://solaraguy.com/viewtopic.php?t=48701
Image
User avatar
xavier
SolaraGuy Street Racer
SolaraGuy Street Racer
 
Posts: 1161
Joined: Wed Jan 26, 2005 6:03 pm
Location: Lancaster, PA

Postby MentatGom » Sat Jun 17, 2006 2:38 am

I use Whiteline parts from http://globalperformanceparts.com/
Swaybar part numbers are:

BTF38 - this is the front swaybar (bushings and some grease included)
BTR39 - this is the rear swaybar (bushings and some grease included)

If you only need bushings:
SPF1132-20K - this is the rear poly bushings
SPF1132-24K - this is the front poly bushings
MentatGom
Just Licensed SolaraGuy
 
Posts: 48
Joined: Mon Nov 29, 2004 6:21 pm
Location: Moreno Valley, CA

Postby TripleBlack » Sat Jun 17, 2006 7:12 am

xavier wrote:check the for sale section. THere is a TRD kit and RSB for sale right now

I see some strut bars for sale, but no sway bars...

MentatGom wrote:I use Whiteline parts from http://globalperformanceparts.com/
Swaybar part numbers are:

BTF38 - this is the front swaybar (bushings and some grease included)
BTR39 - this is the rear swaybar (bushings and some grease included)

If you only need bushings:
SPF1132-20K - this is the rear poly bushings
SPF1132-24K - this is the front poly bushings

Thank you! Perfect. Wonderful.
Proud member of the 49.8% which paid attention last time.
TripleBlack
Regular SolaraGuy Member
Regular SolaraGuy Member
 
Posts: 60
Joined: Tue Jun 06, 2006 8:20 pm
Location: Wayne, NJ

Postby n3985 » Wed Oct 18, 2006 5:53 pm

Sorry to bump a thread but I need some help. My friend has a 99 SE V6 and asked me to install a Whiteline RSb for him. I had him drive on to ramps since I fiugred it is easier than jacking the car up. Removing the stock RSB was simple enough, but we can't get the new one in. The bar hits the protrusion on the gas tank, the shield part held on by a 10mm bolt. Any tips on the install? Thanks
Image
n3985
Just Licensed SolaraGuy
 
Posts: 2
Joined: Mon Oct 16, 2006 9:11 pm
Location: Bloomington, IN

Postby RichD978 » Wed Oct 18, 2006 6:23 pm

its all about angling. Try to slide it in diagonally
Image

http://www.cardomain.com/ride/818696
VOTE FOR ME FOR SHOWOFF OF THE WEEK
RichD978
SolaraGuy Semi-Pro Racer
SolaraGuy Semi-Pro Racer
 
Posts: 3974
Joined: Thu Feb 24, 2005 7:54 am
Location: Northern MA

Postby Nyyankees3511 » Wed Oct 18, 2006 7:37 pm

Try taking the muffler off the rubber holders and that will make it way easier.
1999 SLE Red metallic/black interior
TRD RSB, Jim's Torque rod, K&N, Interior leds
Nyyankees3511
SolaraGuy Driver
SolaraGuy Driver
 
Posts: 942
Joined: Wed Sep 07, 2005 5:31 pm
Location: Lincoln, RI

Postby n3985 » Wed Oct 18, 2006 8:54 pm

We tried angling it diagonally. From what I understand, the bar needs to be on "top" of that gas tank protrusion, but the new bar is too thick to slide in. So is the only way to just play with it? wiggle it here and there?
Image
n3985
Just Licensed SolaraGuy
 
Posts: 2
Joined: Mon Oct 16, 2006 9:11 pm
Location: Bloomington, IN

Postby MentatGom » Thu Oct 19, 2006 2:34 am

So did you remove that heat shield? If so then it should not be a problem. That protrusion itself is flexible, though I experienced no fitment issues. That is really the last positioning I did with the swaybar. I slid it through from the driver's side of the car, getting it through the suspension links, then over the exhaust, and then the links on the passenger side. Once it was in position I lifted it up and actually set the bar on the side opposite that protrusion while I bracketed it up to the chassis. Then all that's left to do are the endlinks.
MentatGom
Just Licensed SolaraGuy
 
Posts: 48
Joined: Mon Nov 29, 2004 6:21 pm
Location: Moreno Valley, CA

Return to Tutorials Gen 1 and 1.5

Who is online

Users browsing this forum: No registered users and 8 guests