Wheel Spacers....

[SteveSolara]

Hey guys I wanted to know if there is a wheel spacer, or a size that will extend the rear out more "Flush" and the front could use it too but especially the rear.

My wheel specs.

17x7" Motegi rims
225/45/R17

So roughly 1/2 an inch or so of space for the rear
Thanks!

[DSM_Lara]

What is your Rim Offset?

Brand Wise I recommend
H&R TRAK+® Wheel Spacers
I have 20mm in the rears with extended studs.
The TRD/Revo rims that I have on now is 17"x8" +40 offset with 20mm spacers at the rear. Tire size is 235/45/17 and its flush at the rear and rubbing again with a rolled fender. -.-

[SteveSolara]

What is your Rim Offset?

Brand Wise I recommend
H&R TRAK+® Wheel Spacers
I have 20mm in the rears with extended studs.

Offset is 40. And 20mm spacers with extended studs, did you have to flare out the fender?

[DSM_Lara]

Actually typo Rolled fenders. Most likely Im rubbing because of the tire size that I have on. 225/45/17 should work better instead of 235.

[SteveSolara]

Hmm thanks!

They had 20mm and 25, no 22mm. Ill go with the 20mm Thanks! the H&R site is Extremely helpful, Thanks again!

[DSM_Lara]

Here's a photo how it sits.

[SteveSolara]

oh Nice! that perfect for me, but you have 235, so a little less. Thanks for uploading. got a better idea how its gonna turn out

[SteveSolara]

hmm everytime i click on "How to buy" it takes me to an applicant and i put in my state, than a couple of stores show up, but none of them have the spacer. I even searched for the part number..... Maybe I have to call the store for special order???

[DSM_Lara]

You can try this site but there are located in California. They shipped to Hawaii so it shouldn't be a problem getting them. I had great experience with them when I needed to order extended studs.
http://www.2kracing.com/Universal_Manuf ... acers.html

If you ever damage your wheel studs here are the specs.
Thread Type: 12 X 1.5
Knurl Diameter: 14.20mm
Thread Length: 50mm (Size may vary but this size will come with 20mm spacers)
Seat Type: Stud
Manufacturer: H&R

[SteveSolara]

Thanks Buddy! Finally get to order them

Center Bore:60.1mm

Just putting this up to if anyone else might go here and was wondering.

Thanks Again!!!

[Mr_Krispy1183]

Have used both Ichiba and H&R to success. I've toned down driving around "fitted", since I commute 70-80 miles round-trip for work, and slightly smaller spacers and a slight raise in the coilovers make the drive much more tolerable, not to mention giving me a little more tire life.

[SteveSolara]

Have used both Ichiba and H&R to success. I've toned down driving around "fitted", since I commute 70-80 miles round-trip for work, and slightly smaller spacers and a slight raise in the coilovers make the drive much more tolerable, not to mention giving me a little more tire life.

HAHAH yea i hear ya. Will be me in a few months. But luckily i dont have coils just springs. So i have some room, just no fat passengers and ill be ok LOL

Thanks for the info

[SteveSolara]

Without Spacer




With Spacers ( I went with 15mm instead )

[yaddadaimsayin]

looks good but that angle makes your car look like it's sittin kinda high. still, pushing the wheels out makes a big difference on the look of the ride. lookin forward to more pics.

[SteveSolara]

Thank you Sir!. Yea pics were a rough take and my hands were all dirty and greased up, sine i did my brakes too while i was at it. And yes it looks high because my driveway is kinda like a little hill so it bring the rear end up. Will update soon.

I can successfully say my rear wheels are rubbing the fenders on tight corner and humps on highways. But hopefully my New RSB to come will fix that

Oh and i am only on TIEN Springs and regular struts so its a bit higher than what the springs go for 2'" but That will change once these struts blow out.